Consolidated many of the add-on's to prevent multiple downloads for first time users (Most notably, Silverfox's Quest Journal reskinning add-on)
Added Geniva's "SlimProfit" Maintained Spells window
Completely replaced the loadscreens to eliminate the "stretched" graphics from the previous version
Made cosmetic changes to the Knowledge book
** The support forums for the EQ2Map mod can be found on the EQ2Interface.com site as well. **
-------------------------------
Fixes
-------------------------------
03 December 2005 - Updated UI to be LU 17 compatible
-------------------------------
Installation notes
-------------------------------
Often, installing a new UI, or upgrading an existing UI will cause certain
windows to move around a bit, and sometimes "disappear". Also, remember
that F10 cycles through the HUD modes, and if inadvertantly bumped, can cause
your UI to disappear. Following is a list of some of the common
"hotkeys" used to make windows visible / invisible.
Clock Window = <ALT> C
Compass Window = <ALT> N
Group Window = <ALT> G
Raid Window = <ALT> R
Guild Window = U
Hotkey Window = <ALT> H
Maintained Spells Window = <ALT> M
Options Menu = <ALT> O
Player Window = <ALT> U
Effects Window = <ALT> E
Quest Journal = J
Quest Helper Window = <ALT> J
Target Window = <ALT> T
If all else fails, I've included 3 "default" character .ini files that can be used to reset the default locations. Please note, using these may cause the loss of any custom chat channels, so I recommend them as a last resort. They are contained within the INI folder of the install instructions, with a README.txt file for installation.
IMPORTANT NOTE:
Install UI And any additional Options Before you install the EQ2Map.
Once the UI is installed, make sure you run the EQ2Map installer PRIOR to
running EQ2 for the first time, or you'll have a ton of UI errors!!!
Right Click Dracokyn.zip, and extract the files someplace easy to find.
Popular places include the desktop, or directly into your
...\EverQuest II\UI directory. Next, we'll move the files
you extracted to the proper locations.
Make sure to place the eq2.ini file into your EQ2 directory. (This controls the UI that loads upon startup)
Under the UI Folder of your EverQuest II directory, copy the Dracokyn folder you unzipped.
-------------------------------
EQ2Map Installation
-------------------------------
After you've copied the folder and eq2.ini file to the proper locations, simply run the EQ2MAP-Updater-1.0.6-Setup.exe file, which is located inside the Dracokyn folder. Make sure the first time you run the Map Auto-Updater that you click the "options" button, and that the UI folder and Everquest II game directories are selected properly. Taco's done a great job with it, and it should auto-update. If you have any problems with EQ2Map, visit the link below.
EQ2Map Troubleshooting & Installation.
-------------------------------
UI Options
-------------------------------
1) To change the "fill" color of the Arcane Orb casting
window or enable the default casting bar:
1) Go to your UI\Dracokyn\images\Arcane folder
2) Rename Orb-purp.dds to Orb-red.dds (this way, you can switch it back later),
as well as Orb-purp-2.dds to Orb-red-2.dds
3) Orb colors to choose from are blue, green, grey, purple, or red. (Orb-XXX.dds)
The default is set to red.
4) Rename the colored orbs (both Orb-XXXX.dds and Orb-XXXX-2.dds) of your choice to Orb-purp.dds
MAKE SURE TO RENAME BOTH THE STANDARD AND -2 files.... otherwise, only one side
of your target bar orbs will change color.
5) If you want the default style casting bar to come up, rename the
eq2ui_mainhud_casting.xml file in the dracokyn folder to
eq2ui_mainhud_casting-OFF.xml
6) If you want to disable the orbs on
the sides of the target window, rename eq2ui_mainhud_target.xml to
eq2ui_mainhud_target-CAST.xml, and then rename eq2ui_mainhud_target-NOCAST.xml
to eq2ui_mainhud_target.xml
2) If you
want to change the target consider system:
While in game, type /con_version 0 for Detailed consider system, and /con_version 1 for the Simple consider system (from within the game)
3) If you want the UI while zoning:
In the UI\Dracokyn folder, rename eq2ui_hud_zoning-OFF.xml to eq2ui_hud_zoning.xml
4) To disable the quest journal modification:
In the UI\Dracokyn folder, rename eq2ui_journals_quest.xml to eq2ui_journals_quest-OFF.xml
5) If you want scroll arrows on your hotkey bar:
1) In the UI\Dracokyn folder, rename eq2ui_mainhud_hotkey.xml to eq2ui_mainhud_hotkey-NOSCROLL.xml
2) Rename eq2ui_mainhud_hotkey-BANKS.xml to eq2ui_mainhud_hotkey.xml
6) If you want the older version Player window (with the %'s over the bars):
1) In the UI\Dracokyn folder, rename eq2ui_mainhud_player.xml to eq2ui_mainhud_player-NEW.xml
2) Rename eq2ui_mainhud_player-OLD.xml to eq2ui_mainhud_player.xml
7) To remove the orbs from the Target / Implied Target bar:
1) In the UI\Dracokyn folder, rename eq2ui_mainhud_target.xml to eq2ui_mainhud_target-ORBS.xml
2) Rename eq2ui_mainhud_target-NO-ORBS.xml to eq2ui_mainhud_target.xml
-------------------------------
Credits:
-------------------------------